Home > Cisco Ip > Cucm Registration Rejected Error Dbconfig

Cucm Registration Rejected Error Dbconfig

Contents

So you need to erase the existing certificates for ITL/CTL first. If you have received this communication in error, please notify us immediately by replying to this message and deleting it from your computer. Ive needed to do this, but not in WebUI. One Cisco Unified CM group which is listed as Default will appear. More about the author

Posts: 334 | From: Madrid | Registered: Apr 2009 | IP: Logged yeungd Guru Member # 25221 Rate Member posted October 15, 2009 04:19 AM Registration Rejected: Error DBConfig Error Message Typically, a Registration Rejected: Error DBConfig message indicates an issue with unassigned directory numbers (DNs). It is the sole discretion of the owner of this website to remove any content if contacted by an outside entity or personally deemed in violation of said policies. Do they have a TFTP IP?

Cucm Registration Rejected Error Dbconfig

Also, make sure that the Cisco CallManager publisher and subscriber run the same version of CallManager. IP gateway or VLAN configuration issues (if the phone and Cisco CallManager server are on different subnets/VLANs). The service releases for Cisco CallManager version 4.1 can be downloaded at Software Download - Cisco CallManager Version 4.1 (registered customers only) .

So the ports that need to be trusted must be enabled with the mls qos trust command in the interface configuration mode of each port. Obtain the configuration file. I can use both images Sub and Pub, and the fail-over works quite well.I have not tested the NTP issue that I was having but suspect that it has been resolved Cisco Ip Phone Registration Rejected Error Mismatch After you click Start, the service can appear to start (the Service Status triangle appears) but then stop again.

See correct answer in context 1 2 3 4 5 Overall Rating: 5 (1 ratings) Log in or register to post comments Replies Collapse all Recent replies first thijs.vandecasteele Wed, 03/27/2013 Cisco Callmanager Phone Rejected It's okay! This issue occurs when the wrong phone type is chosen on the Device > Phone configuration on the CallManager Administration page. Conventions Refer to Cisco Technical Tips Conventions for more information on document conventions.

Brocade ICX: How To Do A Password Reset And Erase Startup-Config Real quick, when booting the 6610 (in my case), press "b" when booting up. Cisco Ip Phone 7940 Registration Rejected I have experience the same exact thing on just about every image I have used, both 4.x and 7.x.After the change from 4.x to 7.x I set out to fix this If you are not the intended addressee, you are hereby notified that you have received this communication in error and that any use or reproduction of this email or its contents What is my TFTP server?

Cisco Callmanager Phone Rejected

There appears to be no routing set up on this router... http://collaboration-ie.com/index.php?/topic/921-registration-rejected-error-dbconfig/ Otherwise, the TFTP server of the Cisco CallManager server sends another File Not Found TFTP response. Cucm Registration Rejected Error Dbconfig This disables DHCP. Cisco Ip Communicator Error Dbconfig Posted by Shane Email ThisBlogThis!Share to TwitterShare to FacebookShare to Pinterest 3 comments: AnonymousOctober 22, 2014 at 12:52 AMyou have to add manually the device and select the appropriate version /model

twhittle1 1 month 1 week ago 128 views Blog C-Series // Resolve Service Profile Association Failure When Incorrect Server Info Given Tray Stoutmeyer 2 months 8 hours ago 31 views Discussion my review here Please upload additional licenses (a new license file) and try again. To learn what takes place at this point, you need to set up a network analyzer to capture the IP packets that the phone sends to and receives from the server. Access lists are often different in each direction. Cisco Ip Phone Registration Rejected Security Error

Error DBConfig? I have several other phones in my voice lab (7921, 7912, 7910, 7940) and all of those register fine. Is auto-registration enabled? click site If the TFTP service does not run, many devices do not boot successfully.

In order to disable DHCP and manually assign IP addresses on a Selsius Phone, complete these steps: Note:During configuration, use "*" instead of ".". Cisco Ip Phone 7942 Registration Rejected For example, enter 10*0*0*100* . Set Enable Caching of Constant and Bin Files at Startup to False.

It appears as the IP address of the servers group at the beginning of the file.

Registration Rejected This means that your IP Phone has already gone through the Phone Boot process and is stuck at step #6,  attempting to register to either the Pub or Sub, Components Used This document is not restricted to specific software and hardware versions. Change the hostname under Server in CUCM to the IP Address of that server.  Otherwise when the IP Phone downloads its configuration file, the hostname of either the Primary or Secondary Cisco Phone Not Registering I urgently need a solution for it.

Components Used The information in this document is based on Cisco Unified Communications Manager 4.x and 7900 Series IP Phones. Are the phones getting an IP address? What's the behavior of the phones after showing the error? navigate to this website telephony-service no auto-reg-ephone load 7941 SCCP41.8-3-3S load 7961 SCCP41.8-3-3S do you have ephone's created with type of 7941 or 7961?

Choose Cisco Phones as the Performance Object. Make sure that Data Collection Enabled is set to True, and click Update. For the Cisco 12 SP+ and the 30 VIP: Press * * to display the status. Thank you. * >> > > jcartier at acs Aug6,2008,9:14AM Post #10 of 20 (14589 views) Permalink Re: 7961 & 7941: Registration Issues [In reply to] Sorry, I actually noticed this mis-configuration before

Did you run >> "create cnf-files" under telephony-service to generate the xml files it's >> looking for? >> >> >> >> -ryan >> >> *From:* Jeff Cartier [mailto:jcartier [at] acs] >> Based on the above result follow the step below to resolve the issue: The standard process is to delete an unused phone from CUCM. All rights reserved. In addition, the server administrator could have changed the default image for a type of phone, or for a specific phone.

Cisco IP Phones Not Registered But seems to be working fine Cisco IP Phones show a status of Not Found or Unregistered on the Cisco CallManager Administration page.